-
$6.00Chain #41 Roller
$6.00Chain #41 Roller used for our Roto Jet Hose Washers.
Price is by the FootChain #41 -
$10.00Dual Purpose Dryer Boot & Glove Hanger
$10.00Dual Purpose Dryer Glove Hanger: Mild Steel 0.19″ diameter rod, chrome plated finish
-
$129.00Dual Purpose Dryer Ceramic Strip Heater
$129.00Dual Purpose Dryer Ceramic Strip Heater 1.5″ Wide X 36″ Long X 0.375″ Thick 1000 Watts / 240 Volts with S.S. Screw Terminals
-
$14.00Dual Purpose Dryer Copper Heater Strip Connector 22″ long
$14.00Dual Purpose Dryer Copper Heater Strip Connector 22″ long
-
$26.00Dual Purpose Dryer Door Handle
$26.00Dual Purpose Dryer Dryer Door Handle (Finish: Bright Chrome .250” mounting holes measure 1.75″ center to center with a 5/16″ square shaft)
-
$25.00Dual Purpose Dryer Door Linkage
$25.00Dual Purpose Dryer Dryer Door Linkage (Used with Part # 25100023)
-
$8.50Dual Purpose Dryer Gear Hanger
$8.50Dual Purpose Dryer Gear Hanger: Mild Steel 0.25″ diameter rod, chrome plated finish
-
$23.00
Dual Purpose Dryer Rigid Door Handle – No Shank
$23.00Dual Purpose Dryer Dryer Ridige Door Handle – No Shank (Finish: Bright Chrome .250” mounting holes measure 1.75″ center to center)
-
$12.00Dual Purpose Dryer Snap Disc Fan Control
$12.00Dual Purpose Dryer Snap Disk Limit / 0.75″ Snap Disc Fan Control, Cut-In- 160 Degrees F, Cut-Out – 200 Degrees F (Open on Rise)
-
$306.00Dual Purpose Dryer Timer Control Circuit Board
$306.00Dual Purpose Dryer Timer Control Panel Circuit Board 12V Control. (Digital LED Display Timer with 2 Easy to Read Red 4 Digit
LED Displays) -
$45.00Dual Purpose Dryer Timer Control Panel Label
$45.00Dual Purpose Dryer Timer Control Panel Label (Used with Part # 10800107).
-
$267.00Fan Motor
$267.00Motor,1/10 HP,Direct Direct Drive Blower Motor, Shaded Pole, Open Air-Over, 1/10 HP, 1550 Nameplate RPM, 115/208-230 Voltage, 42Y NEMA/IEC Frame, Full Load Amps 4.0/2.0-2.0, Service Factor 1.0, 60/50 Hz, Ambient 40 C, Insulation Class A, Number of Speeds 1, Cradle/Stud Mounting, All-Angle Sleeve Bearings, Thermal Protection Auto, Rotation CWSE, Efficiency Group High, Body Dia 5 In, Length Less Shaft 4 15/16 In, Shaft Dia 3/8 In, Shaft Length 2 1/4 In
-
$0.00Hose Dryer Series 100C Manual
$0.00The dual purpose drying cabinet service & operating manual covers safety, operating, maintenance and troubleshooting instructions, complete parts break down along with the products dimensions.
DOWNLOAD INSTRUCTIONS
To get a copy of this manual, simply add it to your shopping cart, checkout and complete the purchase (there is no charge). After completing your purchase look under “My Account” and you will see a menu item on the left hand side of your screen labeled “Downloadable Products”, click this menu item and you will be taken to a screen where you can download the manual.
Note: This manual is in PDF format and requires that Adobe Reader be installed on your computer. If you do not have Adobe Reader, click here to get yourself a free copy.
-
$5,150.00$5,148.97Retrofit Unit for Circul-Air Dryer
$5,150.00$5,148.97Circul Air has reinvented itself. Our ingenuity puts us in a position to offer a practical way to maintain your fire station’s state of the art status. Your Circul Air Drying Cabinet is a wonderful investment but, as with all investments, it must be maintained in order to remain viable and strong. Our Retrofit Head is a cost effective upgrade prolonging the life of your existing equipment. The Retrofit Head upgrade features a 50% decrease in drying time, and a 50% reduction in energy cost. Our control panel offers various settings for heat drying or an ambient air dry selection.
-
$599.00Roto Jet Hose Washer Motor (DOE rule 2015) Series 100
$599.001 HP 1800 RPM Motor 115/230 Volts Premium Efficiency Motor
-
$69.00Roto-Jet Motor Jack Shaft
$69.00Roto-Jet Motor Jack Shaft on the RTJ-5 & RTJ-3 Hose Washer. (Shaft is 11.38″ Long X 0.75″ Dia. With a 3″ Keyway near the middle of the shaft 5″ from the end with the 1.625″ long X 0.1875″ Keyway on the End and a 1.25″ Long X 0.1875″ Keyway on the Other End)
-
$169.00Roto-Jet Washer #41 12 Tooth Sprocket with #41
$169.00Roto-Jet Washer #41 Chain 12 Tooth Sprocket and a #41 Chain 36 tooth Sprocket Welded Together to Make a Double Sprocket Assembly with a Bronze 0.625″ ID Sleeve Bushing Pressed Into the Double Sprocket Weldment.
-
$20.00Roto-Jet Washer #41 Chain 12 Tooth Sprocket
$20.00Roto-Jet Washer #41 Chain 12 Tooth Sprocket 0.75″ Bore
-
$42.00Roto-Jet Washer #41 Chain 21 Tooth Sprocket
$42.00Roto-Jet Washer #41 Chain 21 Tooth Sprocket 0.75″ Bore
-
$75.00Roto-Jet Washer #41 Chain 36 Tooth Sprocket
$75.00Roto-Jet Washer #41 Chain 36 Tooth Sprocket 0.75″ Bore
-
$15.00Roto-Jet Washer A51 V-Belt
$15.00Roto-Jet Washer A51 V-Belt made of a Rubber Body with Polyester Cords in a wrapped Construction. 0.5” wide 0.3125 thick Outside Length 53”
-
$199.00Roto-Jet Washer Black Nylon Brush
$199.00Roto-Jet Washer Black Nylon Brush Wound on an Aluminum Core 9.0″ X 5.75″ with 2.0″ Brush Length 0.75″ Bore
-
$5.00Roto-Jet Washer Brass Flange Bearing 0.4375 ID X 0.625 OD X 0.75 Long
$5.00Roto-Jet Washer Brass Flange Bearing 0.4375 ID X 0.625 OD X 0.75 Long (Manufactured of pressed copper and tin powders and impregnated with lubricating oil. They are intended by design to be self-lubricating and maintenance free)
-
$10.00Roto-Jet Washer Brass Flange Bearing 0.75 ID X 1.0625 OD X 1.1875 Long
$10.00Roto-Jet Washer Brass Flange Bearing 0.75 ID X 1.0625 OD X 1.1875 Long (Manufactured of pressed copper and tin powders and impregnated with lubricating oil. They are intended by design to be self-lubricating and maintenance free)
-
$2.00Roto-Jet Washer Brass Sleeve Bearing 0.375 ID X 0.5 OD X 0.375 Long
$2.00Roto-Jet Washer Brass Sleeve Bearing 0.375 ID X 0.5 OD X 0.375 Long (Manufactured of pressed copper and tin powders and impregnated with lubricating oil. They are intended by design to be self-lubricating and maintenance free)
-
$59.00Roto-Jet Washer Brush Drive Shaft
$59.00Roto-Jet Washer Brush Drive Shaft on an RTJ-5 Hose Washer. (Shaft is 14.88″ Long X 0.75″ Dia. With a 1.25″ long X 0.1875″ Keyway on One End and a 2″ Long X 0.1875″ Keyway on the Other End)
-
$89.00Roto-Jet Washer Brush Flange Bearing Assembly
$89.00Roto-Jet Washer Brush Flange Bearing Assembly that is Bolted to the Back Plane to Hold the Brushes on one Side and the Drive Sprocet on the Other. (Uses 25100030 for Bearings)
-
$69.00Roto-Jet Washer Brush Idler Shaft for RTJ-5 Washer
$69.00Roto-Jet Washer Brush Idler Shaft on a RTJ-5 & the Drive Shaft on a RTJ-3 Hose Washer. (Shaft is 13.88″ Long X 0.75″ Dia. With a 1.25″ long X 0.1875″ Keyway on One End and a 2″ Long X 0.1875″ Keyway on the Other End)
0 item(s)
- $0.00
